[~H]/wsx1_tapin 2.0 configuration file

[~S] COMMENTS/User comments
[d1]/Date   /{00-CCC-0000}=01-JAN-2009/Enter the last date of modification
[l1]/Line 1 /{CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC}/Custom comments for personal use
[l2]/Line 2 /{CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC}/Custom comments for personal use
[l3]/Line 3 /{CCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCCC}/Custom comments for personal use

[~S] PSWD/Passwords
\LOOP\@\0\2\Passwords (max 3)
[p@]/Password @/{CCCCCCCCCCCCCCC}=pwd-@/You can have up to three passwords stored on the WSX1 unit.<br>Passwords may contain spaces.
\ENDLOOP

[~S] CONFIG/General configuration
[ds]/ds  /{0}={1,0}/Daylight saving time<br>0= No<br>1= Canada/US
[ep]/ep  /{0}={0,7,6,5,4,3,2,1}/Expand pager number digits to: <br>Select from choices list.<br>7-1, 0= no expansion.
[xx]/pr  /{0000000}/Enter the pager number prefix<br>(if needed).<br>Prefix is used in pager number formation, after pager expansion<br>ex:<br>prefix=11111, pager= 002<br>pager number=11111002
[sn]/sn  /{CCCCCCCCCC}=CPU-1/System name<br>Used by Jsm Report software
[cb]/cb  /{CCCCCCCCCC}/Callback string<br>PBX HUNT GROUP EXT + pauses if needed<br>ex: 5321,, (room number will complete)
[mp]/mp  /{CCCCC}={pager,port,dn}/Mapping, (select from choices list)<br>Look for pager number<br>Look for port number<br>Look for DN
[ti]/ti  /{CCCCCCCCC}={monitor,active}/TAP input mode:<br>monitor: listen only to a existing serial link<br>active: we are the TAP input device
[pm]/pm  /{0}={2,1,0}/Tap input mode once logged,<br>after message reception<br>0= Disconnect<br>1= Resend (esc PG1) and wait<br>2= Never disconnect (unless error)
[id]/id= /{CCC}={no,yes}/Repeat "ID=" every two seconds?<br>(Tap input mode)
[ts]/ts  /{0000\_>C<\_0\_0}=9600_N_8_1/Tap input-output settings<br>baud_parity_data_stop<br>baud rate must be 4 digits long<br>ex : 300 must be written as 0300<br>Use RX3,-B4 for TAP in<br>Use RX2,TX2 for TAP out<br>Examples :<br>0300_N_8_1<br>1200_E_7_2
[pp]/pp  /{CCCCCCCC}={tap,csx5_enc,nil}/Pagng output protocol:<br>tap: same as input<br>csx5_enc: JSM paging encoder<br>nil: no paging output

[~S] SPLNK/Pager to Handsets mapping table
\LOOP\@\0\127\Users\8
[un]//{000}=@@@/Jsm user number/indexer [pa]/Pager:/{0000000}/Enter the mapped pager number [po]/Port number:/{0000}/Enter the SpectraLink<br>port number for this handset<br>(4 digits needed) [dn]/DN:/{000000000000}/Enter the directory number as programmed in PBX
\ENDLOOP


[~P]/***END***